batesman

I'm starting to think you folks know everything! So...Hypothetically speaking...Let's say I wanted to change the quality of some of the mods I've installed from 1k to 2k. Would I have to start STEP from the beginning? Or could I update the textures, run the based patch, generate new LODs, and call it a day?

The two in my screenshot below. I followed the DynDoLOD instructions exactly as they were on the 2.2.9.2 guide.

Is it normal for both DynDoLOD mod entries in MO to say "No valid game data"? The ESP appears to be loading fine...

Thanks. Sometimes the solution to the problem is to correctly set one's expectations. :)

Are you saying that the mods are not being applied and that I'm viewing vanilla Skyrim?

After completing my second STEP setup, everything is working fine so far with one small exception. The snow on the mountains is...grainy? Pixelated? It's as if the texture isn't being properly applied. I did search the forums, but didn't see anything quite like this. It's most evident on the hill above the tree. Thoughts?

Thank you for the advice. I did just that on my second STEP setup. My first attempt ended in a CTD during character creation so I started over. This time I kept everything separate unless the guide specifically said to merge.

Well, I'm going to start over from scratch now that I've learned a few things and gone through the setup once. I had a CTD during character creation so I figure something's out of whack. :) That's Ok because I consider this first pass a learning process. On another note, there are many instances where we download and install a main file, then an optional file for the same mod. Or a mod with multiple parts (like Book of Silence). Is it advisable to merge or to keep everything separate? Having gone through this process - I have to say that I'm in slight awe of what it took to pull this guide together.

Uh....That's how I've done it too. I think I'm about to run into some hard life lessons though. I'm at the point of bashed patch creation and the instructions say to "enable all plugins", but does that include the dummy plugins as well? My guess is no.

Sweet! Thanks. I'm sure that after I go through this I will be more comfortable the next time round. As a first timer, the guide is quite intimidating and I'm fearful that I'll screw something up along the way, have to start over, and lose allllll that time. :) I appreciate your assistance very much!

Thanks for the info! Speaking of the Extended Version, that is the route I'm going for this setup. Following the guide, I don't see a specific point where I'm supposed to install the STEP Extended patch - even though it is referenced several times in the guide. Before attempting this setup, I read through the guide twice and have done a keyword search as well. Is it hiding in the detailed instructions somewhere? Possibly in the bashed patch section?

Thank you very much! Suggestions: In the XP32 Maximum Skeleton detailed instructions, remove the reference to FNIS. Or modify it to say "FNIS is required for this mod to work. It will be set up later in the guide." IF the FNIS reference is edited and not removed, then the same messaging should be added to Dual Sheath Redux for consistency. On the FNIS detailed instructions, change the wording to "Users need to run this mod if using Maximum Skeleton, Dual Sheath Redux, or other mods that support/require it. Otherwise, disregard this mod."

First - a BIG thank you to the community for the STEP guide! I appreciate the hard work, effort and commitment it takes to put something like this together. I'm following the step guide and have reached the end of 2.D where XP32 Maximum Skeleton is installed. In the detailed instructions of that mod it says, "Remember to run FNIS after installing all mods." I click on the FNIS link to read more about it. On that page it says, "Users only need to run this mod if also using the Maximum Skeleton, or other mods that support/require it. For STEP, this applies to Dual Sheath Redux, which is listed in the Patches section of the Guide. Disregard this mod if Dual Sheath Redux was not installed." So I go to the Dual Sheath Redux install instructions and there is no mention of FNIS. My question: What is the proper order to run FNIS? Once? Twice? Nonece? Thanks!