Guide:ENBSeries: Difference between revisions
From Step Mods | Change The Game
Line 363: | Line 363: | ||
You can adjust the quality and effect of bloom in the ''[BLOOM]'' section of the file. | You can adjust the quality and effect of bloom in the ''[BLOOM]'' section of the file. | ||
This setting is the quality of the Bloos effect, either 0, 1, or 2. 0 is the highest quality and 2 is the highest performance. It is not recommended to set this to anything other than 0, since the performance increase is minimal. | |||
<pre>Quality=(0,1,2)</pre> | <pre>Quality=(0,1,2)</pre> | ||
The following settings | The following parameters determine how much Bloom to add. The settings are from 0.0 to 1.0 and the higher the value the more Bloom blurs and adds a slight lighting effect to the scene. If using an ENB Profile then it is recommended to not change these settings. | ||
<pre> | <pre>AmountSunrise=(0.0...1.0)</pre> | ||
AmountSunrise=0. | <pre>AmountDay=(0.0...1.0)</pre> | ||
AmountDay=0. | <pre>AmountSunset=(0.0...1.0)</pre> | ||
AmountSunset=0. | <pre>AmountNight=(0.0...1.0)</pre> | ||
AmountNight=0. | <pre>AmountInteriorDay=(0.0...1.0)</pre> | ||
AmountInteriorDay=0. | <pre>AmountInteriorNight=(0.0...1.0)</pre> | ||
AmountInteriorNight=0. | The following parameters determine how much blue coloring to add to objects affected by Bloom. The settings are from 0.0 to 10.0, but going below 1.0 will remove most blue color from Bloom. If using an ENB Profile then it is recommended to not change these settings. | ||
BlueShiftAmountSunrise=0. | <pre>BlueShiftAmountSunrise=(0.0...1.0)</pre> | ||
BlueShiftAmountDay=0. | <pre>BlueShiftAmountDay=(0.0...1.0)</pre> | ||
BlueShiftAmountSunset=0. | <pre>BlueShiftAmountSunset=(0.0...1.0)</pre> | ||
BlueShiftAmountNight=0. | <pre>BlueShiftAmountNight=(0.0...1.0)</pre> | ||
BlueShiftAmountInteriorDay=0. | <pre>BlueShiftAmountInteriorDay=(0.0...1.0)</pre> | ||
BlueShiftAmountInteriorNight=0. | <pre>BlueShiftAmountInteriorNight=(0.0...1.0)</pre> | ||
</pre> | |||
[CAMERAFX] | |||
Amount of lens effects added, and will trigger when looking at a bright surface, like the sun. This section will not do anything if there is no Bloom added or if it is disabled. | |||
The following paremeters determine the intesity of the lens effects when looking at bright surfaces. The settings go from 0.0 to 10.0. If using an ENB Profile then it is recommended to not change these settings. | |||
<pre>LenzReflectionIntensitySunrise=(0.0...1.0)</pre> | |||
<pre>LenzReflectionIntensityDay=(0.0...1.0)</pre> | |||
<pre>LenzReflectionIntensitySunset=(0.0...1.0)</pre> | |||
<pre>LenzReflectionIntensityNight=(0.0...1.0)</pre> | |||
<pre>LenzReflectionIntensityInteriorDay=(0.0...1.0)</pre> | |||
<pre>LenzReflectionIntensityInteriorNight=(0.0...1.0)</pre> | |||
This is the sensitivty of the lens effect where higher values create lens reflections only for bright light sources. Values lower than 1 will generate reflections. The settings go from 0.5 to 10.0. If using an ENB Profile then it is recommended to not change these settings. | |||
<pre>LenzReflectionPowerSunrise=(0.0...10.0)</pre> | |||
<pre>LenzReflectionPowerDay=(0.0...10.0)</pre> | |||
<pre>LenzReflectionPowerSunset=(0.0...10.0)</pre> | |||
<pre>LenzReflectionPowerNight=(0.0...10.0)</pre> | |||
<pre>LenzReflectionPowerInteriorDay=(0.0...10.0)</pre> | |||
<pre>LenzReflectionPowerInteriorNight=(0.0...10.0)</pre> | |||
== Adjusting the SSAO Quality == | == Adjusting the SSAO Quality == |
Revision as of 02:22, September 21, 2013
Template:Notice A comprehensive guide for properly setting up ENB for n00bs and gurus alike -- by the Wiki Editors & S.T.E.P. Team
- Updated: 2:22:33 21 September 2013 (UTC)